Williams Sound DLT 100 2.0 Uživatelský manuál stáhnout pdf (Strana 10)

DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver

Programming the Digi-Wave™ System: DLT 100 2.0 Optional Settings

Secure Key Code:

When a group has been set up and the same Secure Code has been entered into all the DLT 100 2.0’s, the DLT 100 2.0’s

without this Secure Code entered cannot listen in on the group. This may be desirable in private or high security-level functions.

The same four digit code must be programmed into all of the DLT’s, Chairman Master, Chairman Slave and Slaves. If a dierent

secure code has been entered, participants cannot re-enter the group without re-entering the correct secure code. The only time

the Secure Code is displayed is when it is being entered. To block users from entering the set-up mode, refer to the SET-UP

LOCK (SLOC) feature (below).

1. Choose a 4 digit numerical code; i.e. 1357. You must use the same code on each DLT in the group.

2. Start with the Chairman Master when programming.

3. With the DLT 100 2.0 turned on, hold the

and buttons simultaneously for two seconds to enter the set-up menu.

4. Use the menu button

to scroll through the menu pages until you get to the screen displayed in gure 1.

5. The rst dash will be blinking (gure 1); using the

button, enter rst digit of the code (0 – 9).

6. Press the menu button

again to move to the second dash which will now be blinking.

7. Enter the next digit and continue until all four digits have been entered.

8. One more press of the menu button

and you will see the word CodE displayed (gure 2).

9. With the Secure Key Code entered, exit the set-up menu by holding the

and buttons

simultaneously for two seconds.

10. Follow the same process with the Chairman Slave and Slave units.

NOTE: There will be fewer pages to scroll through on the Chairman Slave and Slave units to get to the code

set-up screen.

SET-Up Lock (SLOC)

Set-up Lock enables the Administrator to prevent unauthorized changes to the system set-up.

NOTE: Each DLT 100 2.0 has to be locked and unlocked individually.

1. Press

twice, then twice (

-v-v). This has to be done within 5 seconds. ‘SLOC’ will appear

momentarily on the screen (gure 3). SLOC is now enabled.

2. When SLOC is enabled, if a user tries to change any setting by entering the set-up mode, ‘SLOC’ will

appear momentarily on the screen. See gure 3.

3. To unlock this feature, the same (

-v-v) sequence must be entered. There will be no prompt showing

that SLOC was disabled. Accessing the set-up mode is the indication that SLOC is disabled.

NOTE: Each DLT 100 2.0 has to be locked and unlocked individually.

Attendee Checking

When the Master Chairman presses the MENU button once, the number of SLAVE devices connected to the system will be

displayed for two seconds. Addresses 0 - 99 must be used for attendee checking feature. Addresses over 99 will not be

registered. ie: C 12 = 12 DLT’s synched with CM

Tone Control

1. With the DLT 100 2.0 powered ON, press and hold the – and + buttons simultaneously for 2 seconds.

2. The LCD will display the last tone setting t: (1 - 9). See Figure 4.

3. Using the -/+ buttons

, adjust the tone up or down.

1 = Most bass response

5 = Flat (Default)

9 = Most treble response

4. Press and hold the – and + buttons

simultaneously for two seconds to save the tone setting.

A147

A149

FIGURE 1

FIGURE 2

A148

FIGURE 3

A146

FIGURE 4

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 31 32

Komentáře k této Příručce

Žádné komentáře

Williams Sound DLT 100 2.0 Uživatelský manuál Strana 10

Komentáře k této Příručce

Související produkty a manuály pro Přijímač Williams Sound DLT 100 2.0